MC56F8000RM中文資料飛思卡爾數據手冊PDF規格書

56F8013/56F8011 Description

The 56F8013/56F8011 is a member of the 56800E core-based family of Digital Signal Controllers (DSCs). It combines, on a single chip, the processing power ofa DSP and the functionality of a microcontroller with a flexible set of peripherals to create an extremely cost-effective solution. Because of its low cost, configuration flexibility, and compact program code, the 56F8013/56F8011 is well-suited for many applications.

56F8013/56F8011 Features

Digital Signal Controller Core

? Efficient 16-bit 56800E family Digital Signal Controller (DSC) engine with dual Harvard architecture

? As many as 32 Million Instructions Per Second (MIPS) at 32MHz core frequency

? Single-cycle 16 ×16-bit parallel Multiplier-Accumulator (MAC)

? Four 36-bit accumulators, including extension bits

? 32-bit arithmetic and logic multi-bit shifter

? Parallel instruction set withunique DSP addressing modes

? Hardware DO and REP loops

? Three internal address buses

? Four internal data buses

? Instruction set supports both DSP and controller functions

? Controller-style addressing modes and instructions for compact code

? Efficient C compiler and local variable support

? Software subroutine and interrupt stack with depth limited only by memory

? JTAG/Enhanced On-Chip Emulation (OnCE) for unobtrusive, processor speed-independent, real-time debugging

Memory

? Dual Harvard architecture permits as many as three simultaneous accesses to program and data memory

? Flash security and protection that prevent unauthorized users from gaining access to the internal Flash

? On-chip memory:

— 16KB of Program Flash (56F8013 device)

12KB of Program Flash (56F8011 device)

— 4KB of Unified Data/Program RAM (56F8013 device)

2KB of Unified Data/ProgramRAM (56F8011 device)

? EEPROM emulation capability using Flash

Peripheral Circuits for 56F8013/56F8011

? One multi-function six-output Pulse Width Modulator (PWM) module

— Up to 96MHz PWM operating clock

— 15 bits of resolution

— Center-aligned and Edge-aligned PWM signal mode

— Four programmable fault inputs with programmable digital filter

— Double-buffered PWM registers

— Each complementary PWM signal pair can outputdifferent switching frequency by selecting PWM generation sources from:

– PWM generator

– External GPIO

– Internal timers

– ADC conversion resultof over/under limits:

– When the conversion result is greater than high limit, deactivate PWM signal

– When the conversion result is less than low limit, activate the PWM signal

? Two independent 12-bit Analog-to-Digital Converters (ADCs)

— 2 x 3 channel inputs

— Supports both simultaneous and sequential conversions

— ADC conversions can be synchronized by both PWM and timer modules

— Sampling rate up to 2.67MSPS

— 8-word result buffer registers

— ADC Smart Power Management (Auto-standby, auto-powerdown)

? One 16-bit multi-purpose Quad Timer module (TMR)

— Up to 96MHz operating clock

— Four independent 16-bit counter/timers with cascading capability

— Each timer has capture and compare capability

— Up to 12 operating modes

? One Serial Communication Interface (SCI) with LIN Slave functionality

— Full-duplex or single-wire operation

— Two receiver wake-up methods:

– Idle line

– Address mark

? One Serial Peripheral Interface (SPI)

— Full-duplex operation

— Master and slave modes

— Programmable Length Transactions (2 to 16 bits)

? One Inter-Integrated Circuit (I2C) port

— Operates up to 400kbps

— Supports both master and slave operation

? Computer Operating Properly (COP)/Watchdog timer capable of selecting different clock sources