TJA1081B集成電路（IC）的專用規(guī)格書PDF中文資料

General description

The TJA1081B is a FlexRay node transceiver that is fully compliant with the FlexRay

electrical physical layer specification V3.0.1 (see Ref. 1). In order to meet the

JASPAR-specific requirements, it implements the ‘Bus driver increased voltage amplitude

transmitter’ functional class. It is primarily intended for communication systems from

2.5 Mbit/s to 10 Mbit/s and provides an advanced interface between the protocol

controller and the physical bus in a FlexRay network.

The TJA1081B features enhanced low-power modes, optimized for ECUs that are

permanently connected to the battery.

The TJA1081B provides differential transmit capability to the network and differential

receive capability to the FlexRay controller. It offers excellent EMC performance as well as

effective ESD protection.

The TJA1081B actively monitors system performance using dedicated error and status

information (that can be read by any microcontroller), along with internal voltage and

temperature monitoring.

The TJA1081B supports mode control as used in the TJA1080A (see Ref. 3) and is fully

function and footprint compatible with the TJA1081 (see Ref. 2).

Features and benefits

Optimized for time triggered communication systems

? Compliant with FlexRay electrical physical layer specification V3.0.1 (see Ref. 1)

? Meets JASPAR requirementsasdescribedinthe ‘Busdriverincreasedvoltage

amplitudetransmitter’functionalclass

? Automotive product qualification in accordance with AEC-Q100

? Data transfer rates from 2.5 Mbit/s to 10 Mbit/s

? Supports 60 ns minimum bit time at 400 mV differential input voltage

? Very low ElectroMagnetic Emissions (EME) to support unshielded cable, meeting

latest industry standards

? Differential receiver with wide common-mode range for high ElectroMagnetic Immunity

(EMI), meeting latest industry standards

? Auto I/O level adaptation to host controller supply voltage VIO

? Can be used in 14 V, 24 V and 48 V powered systems

? Instant transmitter shut-down interface (via BGE pin)

? Independent power supply ramp-up for VBAT, VCC and VIO3

Low-power management

? Low-power management including inhibit switch

? Very low current in Sleep and Standby modes

? VBAT operating range: 4.75 V to 60 V

? Gap-free specification

? Local and remote wake-up

? Supports remote wake-up via dedicated data frames

? Wake-up source recognition

Diagnosis (detection and signaling)

? Enhanced supply monitoring of VBAT, VCC and VIO

? Overtemperature detection

? Short-circuit detection on bus lines

? VBAT power-on flag (first battery connection and cold start)

? Clamping diagnosis on pin TXEN

? BGE status feedback

Protection

? Bus pins protected against ?6 kV ESD pulses according to IEC61000-4-2 and HBM

? Pins VBAT and WAKE protected against ?6 kV ESD pulses according to IEC61000-4-2

? Bus pins protected against transients in automotive environment (according to

ISO 7637 class C)

? Bus pins short-circuit proof to battery voltage (14 V, 24 V and 48 V) and ground

? Fail-silent behavior in the event of an undervoltage on pins VBAT, VCC or VIO

? Passive behavior of bus lines while the transceiver is not powered

? No reverse currents from the digital input pins to VIO or VCC when the transceiver is not powered

Functional classes according to FlexRay electrical physical layer

specification (see Ref. 1)

? Bus driver voltage regulator control

? Bus driver - bus guardian interface

? Bus driver logic level adaptation

? Bus driver remote wake-up

? Bus driver increased voltage amplitude transmitter (JASPAR)